“I’ve done things without using reamp boxes, where I have literally taken a signal from my hardware insert and sent it to the guitar pedals, but you have to turn your output down dramatically. That really is the job of the reamp box.” You should be able to keep it at whatever level you do inside of your DAW and never have an issue driving it too hard - or not hard enough - into a reamp box. The output signal is so hot compared with an instrument level, so if the reamp is doing its job properly there shouldn’t be any issues. “The reason for using a reamp box is so you can take a balanced line signal from a mixer or an interface. “The good quality reamps I’ve used don’t have any real level issues,” says Huart. When you want to recall a mix at a later date, there’s less setup time because the effects that you created by reamping and running through guitar pedals are printed back in permanently on a mono or stereo track and are available immediately for remixing. However, most mixers, myself included, like to print what we do because it makes mix recalls much easier,” Huart says. “You can go out of one, back in on one, run it in real time during a mix, and you don’t have to print it.
#Build a reamp box pro
“You select the output of your DAW, come out of your interface through the pedals, and then back into an input on your interface.”įor instance, that would be true of Pro Tools hardware inserts, he says. “Some interfaces allow you to run the pedals as a hardware insert, which means you don’t have to record them,” says Huart. Here’s a closer look at three popular, affordable DAWs.
#Build a reamp box free
The Best Free Recording Software: Three Economic DAWs to Get You Startedĭigital Audio Workstations (DAWs) are an essential part of any recording setup, even in modern analog environments. “If it’s just going through the guitar pedals, you’ll come out of your pedals, and then go back into the instrument line input on your interface, and you’ll record it back in that way,” Huart says. If you’re using a guitar amp, and not just the pedals, you’ll obviously need to mic your amp, and that microphone will have to go back into the mic pre on your interface. Check your reamp box and obviously your I/Os as to which ones you need.” Pedals and Amps “It’s either going to be an XLR cable to an XLR cable, an XLR to a stereo balanced ¼-inch, or a balanced 1/4-inch output to a balanced ¼-inch input. “Make sure that you match your inputs and outputs correctly, and remember that balanced line signals are three pins, not two,” Huart says. “If your output is a balanced line from an XLR, you’re going to have to get an XLR-balanced cable and make that go to a ¼-inch balanced cable on most of these reamp boxes.” Some reamp boxes do take XLR in, and if that is the case, it will make life easier, however, some more affordable ones have only ¼-inch inputs. “Many interfaces, especially on at the ‘prosumer’ level, are going to have a ¼-inch instrument input,” Huart says. Start by reviewing and understanding the inputs and outputs of your interface and be certain that you have all of the right cables.
“It gives you another palette, a selection of organic analog equipment, that you can use,” Huart says. You can then use all of your guitar pedals as your front end and put that back into a guitar amp or directly back into your DAW (digital audio workstation).”įor example, his colleague Bob Horn, engineer/producer for Usher, Nelly, Everclear and Timbaland, uses guitar pedals on his mixes and not just for guitars, but for vocals, keyboards, drum loops or anything. “That goes through the reamp into your normal guitar chain. “This allows you to send a direct clean signal off of your computer,” Huart says. How Reamp Boxes WorkĪll reamps take a balanced line-level signal from either a mixer or an interface and make it into an unbalanced instrument-level signal that can be handled by a guitar amp.
#Build a reamp box how to
In this tutorial, Warren Huart explains reamping and how to get the best results in the most practical ways. For the guitarist on a budget, Saturnworks, Switchcraft and Radial offer affordable options. If you want to reamp, you’ll find plenty of reamp boxes on the market, including some that won’t empty your wallet. “Printing a DI gives you a lot of flexibility when it comes to mixing, especially if you don’t mix your own stuff and you give it to somebody who wants to dramatically change your guitar sounds to fit their vision of how your song should be mixed,” Huart says.
0 kommentar(er)
